라운드받침대

페이지 정보

profile_image
작성자대구막창 조회 0회 작성일 2021-11-25 15:08:13 댓글 0

본문

라운드 작품 2. 컵받침대 만들기

라운드 뜨개룸으로 컵받침를 만들어 봅시다.

DIY 라운드 컵받침/ 자유롭게 박아서 만드는 cup coaster/짜투리천활용 [탐나는쏘잉]

심심한 원단에 자유롭게 막~ 박아서 패턴을 그려서 컵받침을 만들어 봅니다.
라운드 컵받침만들 때 창구멍 남기는 2가지방법 알려 드려요.

짜투리천 남을때마다 만들어 두면, 나눠쓰기도 좋고, 가볍게 선물하기도 좋은 아이템이죠. 컵받침.

저는 한동안 미싱을 안하다가 미싱자리에 앉아서 워밍업할 때 이렇게 작은 것들을 만든답니다. 소소한 손풀기로...

/ 사이즈는 지름 11cm로 만들었는데, 더 크게도 만들어 보세요.
요즘은 컵받침이 커지고 있는것 같아요.

/이번 영상에는 음성을 빼 봤어요. (영상작업속도를 조금 높여 보려구요.)
정보는 잘 전달되면서 효율적인 작업 방식을 계속 찾고 있답니다.
댓글로 여러가지 의견 남겨주시면 참고할께요.
항상 즐거운 쏘잉하시고~ 또 뵈요.






#cupcoaster #컵받침만들기 #탐나는쏘잉
바이수 : 티매트느낌 너무좋아요~❤ 뒷감 창구멍 꿀팁 감사해욥!!♡
Hello ojae헬로오재 : 중심에 창구멍을 내는건 정말 좋은 방법같아요 소중한 팁들 감사하게 봤어요^^
쉽게 알려주는필아트DIY : 인스타그램에서 보구 찾아왔어요~
이거 너무 해보고싶어서~ㅋ
원형가운데 창구멍~해봐야겠어요
늘 원형창구멍바느질하기 힘들었는데...
좋은꿀팁 감사해요~
320번째 구독 누르고갑니다~
행복한월욜되세요~
희즈돌 : 인스타 인친후 이제 들어와봐요 선생님 유튜브^^ 오늘 구독 꾹 누루고 갑니다! 희즈돌에도 놀러와주실꺼죠^^
최지혜 : 출석 꽝꽝!!^^

HOW TO | Round Coffee Table

Today we're building a Circle Coffee table from start to finish!
Every step from taking materials out to Oiling the final product.
____________________________________________
1.Hey Guys, unfortunately today's video doesn't have any epoxy, But, we are going to show you how to build this white oak coffee table
2.The first step is to pull the required material. Luckily we had some white oak shorts that were off cuts from another job so we'll use those for this build
3.You want to make sure the material is fairly straight to eliminate waste and to achieve the desired thickness for the table.
4.Once you've pulled enough material for your table build, it's time to machine the material.
5.First step is to face joint the material to give ourselves a flat surface on one of the faces of the material.
6.This flat surface will be a great reference point for when the boards go through the planer.
7.After your boards have been face jointed, you can take them to the planer to clean up the opposite side of the board.
8.It will take a few passes for the planer to take the material down to a useable flat surface. You'll want to remove about 1/16" of material at a time.
9.When glueing up a panel, it is important to be prepared and have all your clamps close by for a stress free glue up.
10.You're going to want to make sure you alternate the end grain on each board to eliminate warping.
11.Wood will typically cup away from the center of the tree so by alternating the grain you are averaging out the movement of each board.
12.Once you've applied glue to the edge of each board, you can clamp the pieces together and wipe off the squeeze out.
13.Wiping off the excess glue here will make sanding the surface easier and more efficient.
14.There are many ways to cut a circle for the table top and for this project, we chose to use shaper.
15.We cut all our finger joints on the Table Saw using this finger joint jig.
16.Cutting finger joints can be an intimidating task but with a finger joint jig, they can be easily cut and reproduced for future projects.
17.The most important dimension of the finger joint jig is making sure your dad stack, matches the fence/guide.
18. The other important dimension is making sure the gap between the dado stack and fence equals the width of the dado stack and the fence.
19.Making sure these 3 dimensions all match are key as well as making sure that dimension is divisible by the overall width of the table leg you are creating.
20.It's important to sand your table legs before you attach them to the table top. This will allow you to easily sand all areas of the legs without the table top getting in the way.
21.We are now ready to attache the table top to the table base.
22.For this we will be using Festool Dominos to make sure the base is perfectly aligned on the table top.
23.We always test fit the base to the top to make sure the glue up will go smoothly.
24.Now that we've got the table assembled and sanded to 150 grit, we are ready to apply the oil finish.
25.We use Rubio Monocoat Pure 2C Oil on most of our projects because it protects the wood and its a very user friendly product.
26.After we mix the oil with the hardener in a cup, we apply the oil with a squegee or a spreader. You can also use an old credit card if you don't have a squeegee handy.
27. We always do the bottom of the table first and the flip it over and do the top.
28.After the oil is generously spread across the work piece, you are going to want to wipe the oil off using blue shop towels or a terry cloth. .
29.The key to wiping the oil off is to make sure you get all the excess oil off. You want to keep wiping until no oil is coming up on the towels and using new towels once they've become saturated.
30. The oil takes 7 days to fully cure but you can handle/use the piece after 24 hours.

Let us know if you have any questions or suggestions for future videos.
______________________________________________________

Follow us on our other platforms!

Website ➤ https://jeffmacksupply.com/
Instagram ➤ https://www.instagram.com/jeffmackdesigns/
Shop Instagram ➤ https://www.instagram.com/jeffmacksupply/
Facebook ➤ https://www.facebook.com/JeffMackDesigns/

#RoundCoffeeTable #HowTo
Jeff Mack Designs : Thank you for the feedback on the video! The audio is noted and we'll avoid it for future videos!
If anyone had a hard time hearing we've linked all the instructions in the description.
Michael : Looks great, nicely done. The one thing you mentioned about wiping off the glue after glue up especially with an open grain wood is that by wiping it off you’re forcing the glue residue into the grain and unless 100% sanded out and you can’t be sure, it will affect the absorption of any stain. What I do it wait till the glue sets for about 45 minutes and gets rubbery and then I use a scraper to remove the squeeze out.
N U : Great Video. This has given me some invaluable insight. I’m building a round coffee table, with the same legs. Do you have any suggestions for joining up the legs with less sophisticated tools (I just have a drill, orbital sander and circular saw and a few clamps - no table saw). Navigating the angles for the gluing/joining the legs has been giving me sleepless nights. Any advice will be much appreciated. Thanks
Michael : Hey guys, great build. I’m getting reading to build a 40” round coffee table pretty similar to yours and an expandable farm table and will be looking at this Rubio oil as a finish. Never heard of it but I like what I see. Thanks. btw, I subscribed to your channel. I love the way you guys did this video and the text below that you included. I just looked you up on Instagram to follow you and I already am
Michael : Hey guys, I’m building a round coffee table pretty similar to the one you’re doing here. I have the Domino 700 XL and I’m trying to figure how to reference the position of the mortises on the underside of the table. I’ll use the fence set at 15 MIL for the vertical supports but how to you reference the cut on the underside of the table. You all just show gluing and lining up but how did you reference to get them to line up correctly?

... 

#라운드받침대

댓글목록

등록된 댓글이 없습니다.

전체 6,750건 1 페이지
게시물 검색
Copyright © www.navi-1.co.kr. All rights reserved.  Contact : help@oxmail.xyz